Grounding ESD Flooring
Poured ESD - Static Control Epoxy Floors
[Home]
[Static Control Vinyl Tile] [Static Control Carpeting] [Static Control Rubber Flooring]
[ESD Epoxy Flooring] [ESD Accessories] [Static Control Anti-Fatigue Flooring/Runners]
[Anti Static Chemicals] [Moisture Barrier Systems]

ESD / Static Control Poured Epoxy Flooring

Which ESD flooring is best for you? Use the
ESD Flooring Selection Chart to find out.
adobeAdobe Acrobat Required


ZeroStat Crete

Alcom
Stencil your company logo on your epoxy floor-also add a welcome for your international clients.

ZeroStat Crete Fundamentals

Static-Conductive Water Based Epoxy Concrete Finish

  • Economical, state of the art, permanent conductive formulation.
  • Hard extended wear performance, never requires ESD Wax.
  • Water based, easy application and cleanup
  • Excellent chemical resistance.
  • Extremely cost effective and NOT humidity dependant.
  • Fast, low cost installation, minimal prep requirements.
  • Lowest installation odor in the industry

ZeroStat Crete incorporates state-of-the-art, static conductive properties into a high performance, two-component, water-based epoxy for use on concrete and other hard surfaces. ZeroStat Crete provides outstanding durability and abrasion resistance while eliminating electrostatic charges which can damage or destroy sensitive electronics components or equipment. ZeroStat Crete also displays superb resistance to a wide variety of chemicals and solvents commonly found in industrial and commercial environments, without the toxicity and disposal considerations associated with some solvent systems. When cured, ZeroStat Crete exhibits characteristics superior to solvent-based polyurethane, and rivaling those of solvent-based epoxy coatings. ZeroStat Crete produces superior results when used on all interior concrete, stone and ceramic surfaces.

ITEM DESCRIPTION SIZE
ZS-CRETE-Q ZeroStat Crete Quart
ZS-CRETE-G ZeroStat Crete 1 gallon
ZS-CRETE-5 ZeroStat Crete 5 gallon pail

Available in the following colors:

ZS-Crete Colors

SPECIFICATIONS

Standard color Medium Gray, Low Glare Finish
Solids 37% +/- 1%
Static Decay .02 seconds
pH 6.0 - 7.0
Weight per Gallon 9.5 - 9.6 pounds

Hardness
30 (Sward)
Static Conductive 104-106 ohms
Viscosity H - J (Gardner)
Solvents Water - Glycol
Flash Point 142° F
Dry Time Touch; 7 hours, Moderate traffic; 12 hours, Full cure 7 days
Coverage 250 - 600 ft2 per gallon

APPLICATION AND MAINTENANCE

Ingram Micro

For Detailed Instructions on how to install ZeroStat Crete, Click Here-->

Overview: New concrete floors should be allowed to cure for thirty days. Applications to floors colder than 60° F is not recommended. Sweep and mop contaminated floors with Brut, Grease Strip of Citru-Gest to remove oil, grease and soil. With contaminated or exceedingly smooth troweled floors follow by etching with Ground Zero Prepare, then thoroughly rinse with water. If floor has been previously coated, a small area should be cleaned and roughed up by a screen disking with a 80 grit screen. Test ZeroStat Crete for adhesion, lifting etc. Any area's of the existing coating which display poor adhesion should be stripped. Wash the stripped area's, acid etch, and rinse thoroughly. Allow the floor to dry. Catalyzed ZeroStat Crete should be used within six hours of mixing, therefore prepare only the quantity necessary for immediate use. Add the pre-measured catalyst to epoxy base. Stir gently until the catalyst has been thoroughly mixed in. Allow catalyzed mixture to stand 5 minutes. Apply catalyzed ZeroStat Crete with a short nap roller in thin uniform coats. The initial coat will cover approximately 250 to 500 ft2 per gallon. Second coat coverage is approximately 400 to 600 ft 2 per gallon . Note: This product is not recommended for applications that experience reoccurring standing water.

ZeroStat Crete is a thin set epoxy (approximately 3 to 7 mil thickness), much tougher and longer lasting that ESD paints. Due to it's reduced solids count and thin set benefits ZeroStat Crete may exhibit slight variances in texture and color. These variances do not affect the excellent electrical performance or wear characteristics. ZeroStat Crete is only available in Gray and features a non glare finish. For extended color options and fill applications (up to 125 mil thickness) please give us a call.


Technical Documents:

» ZeroStat Crete Fundamentals Data Sheet
» ZeroStat Crete MSDS Sheet
» ZeroStat Crete Part A & B MSDS
»ZeroStat Crete Fundamentals Installation

arrow Home
ZS Crete Fundamentals
ZS Crete Premier
arrow